行业动态【ENTERPRISE NEWS】

当前位置:网站首页 > 新闻资讯 > 行业动态
  • 轻质隔墙板的安装方式介绍
  • 本站编辑:杭州久泰建材有限公司发布日期:2020-03-04 16:57 浏览次数:
轻质隔墙板的安装方式
 
1、按实际图纸清楚预砌墙定位出墙,地,顶,梁等表面的浮尘和多余灰浆,平整表面。
 
2、设计要求做导墙时可以做预制混凝土垫块,也可做现浇混凝土导墙。其中导墙中心线应与砌块墙中心线一致。
 
3、砌体墙砌筑前沿隔墙长度方向计算块数,比较后不足一块的空隙,可将砌块据成需要的尺寸填补空隙。砌体墙一般无需抹灰,砌筑时应采取自下而上阶梯形式的砌筑方式,要求上下缝为错缝排列。
 
4、放线、运板就位:在安装墙板的轴线分别上下弹出板厚的双线,根据需要的规格抬到墙边。
 
5、锯板:根据墙体的规格任意用手提电锯切割。
 
6、上浆:先在两块板的榫边水泥一道,再将聚合物砂浆任意抹在一块榫边上。
 
7、安装:将准备安装的条板搬到装拼位置,用铁橇将墙板校正,用力橇靠紧,使聚合物砂浆从接颖挤出至饱满,再用木楔将其临时固定。
 
8、校正、固定;用2米或2米以上的靠尺检查垂直、平整校正,再用Φ6mm或Φ8mm带肋的钢筋加建筑胶固定。
 
9、灌浆、补浆;将校正后的墙体墙壁板用聚合物砂浆补满、刮平、上下间隙大的用细石混凝土填补。
 
10、贴防裂布:在灌缝聚合物及墙体全部定型后,在所有的接缝处用乳胶将玻纤布贴上。
 
11、安装电线、开关:将要设暗线、开关盒位置放线,再用手提电锯切割开槽,安装完毕后用聚合物砂浆补平。
 
12、装门框:在安装好的墙上预留门窗洞口,随意用夹板或线条锚固。
 
13、饰面瓷砖、装饰板;在装好的墙体上不需抹灰则可随意粘贴瓷砖或其他木饰面板。
 
14、电器安装:在装好的室内随意安装灯具、家具、空调、可钉可挂。

Light Partition Board Installation 1, according to the actual drawings clearly pre-masonry wall positioning out of the wall, floor, roof, beams and other surface dust and excess mortar, flat surface. 2, the design requirements do guide wall can do precast concrete pad, can also do cast-in-place concrete guide wall. The center line of the guide wall should be consistent with the center line of the block wall. 3. Calculate the number of blocks in the length direction of the partition wall in front of the Masonry Wall. Masonry walls generally do not need plastering, masonry should be taken from the bottom to the top of the ladder form of masonry, requires the upper and lower joints for staggered joint arrangement. 4, put the line, the board in place: in the installation of the wall plate axis respectively up and down the two-line plate thickness, according to the need to lift the specifications to the wall. 5, saw plate: According to the specifications of the wall arbitrary with a portable electric saw cutting. 6. SIZING: Cement the edges of two boards together, then apply polymer mortar to any edge of the tenon. 7. INSTALLATION: move the slats ready for installation to the assembly position, align the wallboard with a crowbar, pull the panels close together, extrude the polymer mortar from the joint to a full volume, and then temporarily secure it with a wooden wedge. 8. Correct and fix; check the verticality and flatness correction with a ruler 2 meters or more, then fix it with 6mm or 8mm ribbed steel bar and construction glue. 9. grouting and Grout; fill the corrected wall panel with Polymer Mortar, scrape flat, and fill the gap between the top and bottom with fine stone concrete. 10, Paste anti-crack cloth: After the pouring polymer and the wall are all finalized, in all the joints with latex cloth glass fiber paste. 11, the installation of wires, switches: will be installed dark line, switch box location wire, and then cut a slot with a portable electric saw, after installation with polymer mortar fill flat. 12. INSTALL DOOR FRAMES: leave door and window openings in the installed walls and anchor them with plywood or wire at will. 13. Decorative Tile, decorative board; in the installed wall without plastering, you can paste tiles or other wood decorative panels. 14, electrical installation: in the installed indoor installation of lights, furniture, air conditioning, can nail can be hung.